Search... ELectronics :

Power Amplifier Circuit Design with IC LME49810

Power output level by the two pairs NJL3281D/1302D parallel to better drive 4 Ω impedance of the speakers or less, R19, R20, R22, R23 may be used to inhibit the high-frequency oscillations, from 10 Ω resistance can be. VD1 and VD2 for the protection of output power, to avoid being loaded on the induced voltage damage. VT7 and the surrounding circuit constitutes a bias voltage circuit, in our production, VT7 has been fixed in the power output of the heat sink, we can adjust potentiometer RP1 of resistance, to facilitate adjustment bias current So that the flow RP1 for the current 2.8 mA. The amplifier circuit is part of the feedback loop 2, the audio signal, the feedback loop from the main R11, R12, R30 and C12 components, the amplifier gain of [1 + (R11 + R30) / R12]. At a higher frequency, C11 and C12 can be regarded as short-circuit, the negative feedback to promote the routing level feedback to replace the power output level feedback, to gain power amplifier (1 + R29/R12). This feedback way to increase the stability of the circuit, especially the drive capacitive load of times. Therefore, the amplifier design more suitable for all types and purposes of the circuit experiment.

We generally understand the composition of the circuit, the output protection circuits and DC servo circuit does not draw the map, they will be placed on an independent board and will in the future in an article devoted to. Production process and the value of each component will also be presented in the following article. Readers could be in accordance with their friends in need of output power and circuit configuration calculated and the experimental.

Examples of welding see Figure 1, the transistor can be drive-TO-126 or TO-220 packages, the board reserved the heat sink position. Feedback circuit sampling point is very important, can refer to the original product manuals, in fact, PCB on the copper lines is not zero resistance, see Figure 11, A point and the existence of potential difference point B, B, is the correct Negative feedback sampling point, and point A is not.
Figure 1 using the power amplifier circuit design LME49810

Figure 2 LME49810 amp components Location

0 comments:

Electronics Now

Your Ad Here
User Agreement

The creator of THIS PAGE or the ISP(s) hosting any content on this site take NO responsibility for the way you use the information provided on this site. These circuits here are for educational purposes only and SHOULD BE VIEWED ONLY. If you download any files to view them, you are agreeing to delete them within a 24 hour period. If you are affiliated with any government, or ANTI-Piracy group or any other related group or were formally a worker of one you CANNOT enter this web site, cannot access any of its files and you cannot view any of the HTML files. All the objects on this site are PRIVATE property and are meant for previewing only. If you enter this site without following these agreements you are not agreeing to these terms and you are violating code 431.322.12 of the Internet Privacy Act signed by Bill Clinton in 1995 and that means that you CANNOT threaten our ISP(s) or any person(s) or company storing these files, cannot prosecute any person(s) affiliated with this page which includes family, friends or individuals who run or enter this web site. IF YOU DO NOT AGREE TO THESE TERMS THEN LEAVE.

Disclaimer

All files are found using legitimate search engine techniques. This site does not and will not condone hacking into sites to create the links it list. We will and do assume that all links found on the search engines we use are obtained in a legal manner and the webmasters are aware of the links listed on the search engines. If you find a URL that belongs to you, and you did not realize that it was "open to the public", please use the report button to notify the blogmaster of your request to remove it. This is not an invitation for webblog haters to spam with requests to remove content they feel that is objectionable and or unacceptable. Proof of URL ownership is required.
NOTICE: This Blog Has Already Been Reviewed And Accepted By Blogger.com

© 2013. Another Electronics Circuit Schematics. Powered by Blogger.
 

blogger templates | Make Money Online